Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
We've discovered this great article on How to Install a Bathtub directly below on the web and concluded it made good sense to write about it with you over here.

Setting up a tub isn't precisely rocket science, yet it does call for strong plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging project. If the old tub is conveniently available, the job can move immediately; if you have to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the work and fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly aid you set up a brand-new bath tub in your restroom if you have already gotten a new tub and also don't need to change the plan of your previous water system pipelines.
Your devices and also material list ought to comprise the following:
Planning for the Installation
First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the tub up until the spirit level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as examine all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub needs to wait until the bath tub has actually been used at the very least when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind ought to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture an inflexible seal, causing the water to pass through the wall in between the bathroom and the tiling, resulting in issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I came across that article about Installing A Bathtub while browsing the search engines. Are you aware of anybody else who is serious about the niche? Please feel free to promote it. Thanks a lot for taking the time to read it.
Dial, we'll rush! Report this page